Troubleshooting Tips to Fix Netgear Router Red Light Issue
Gone are the times when users used to be troubled by the Netgear router orange light issue. Now, they have started going nuts because of the Netgear router red light issue. Is the LED on your Netgear wireless router also blinking red? Are you wondering what might be the reasons behind the issue at hand and how you can resolve it? Nodding to that question?
Well then, you have landed on the right article. Here, not only have we talked about the factors that might have contributed to the issue at hand, but also the troubleshooting tips through which it can be put to rest. Taking this into consideration, keep reading.
Netgear Wireless Router Flashing Red [Reasons]
In this section, the topmost reasons behind the Netgear Nighthawk router red light issue have been mentioned:
- Technical glitches are on board.
- Your Netgear router is not properly plugged into its wall socket.
- The Ethernet cable connecting the networking devices is worn out.
- You have not configured your wireless router properly.
- The firmware of your Netgear router is running on an outdated version.
Whether you have performed Netgear AC1200 setup in your home or configured any other Netgear Nighthawk wireless router, the troubleshooting tips discussed below can be implemented for all models. With that said, continue reading.
[Fixed] Netgear Nighthawk Router Red Light Issue
- Power Cycle the Netgear Router
Mentioned as the first reason behind the Netgear router red light issue, technical glitches are known to impact the overall performance of a device. In order to get rid of them, a simple hack ought to be implemented, i.e. power cycle the Netgear wireless router.
In order to power cycle your Netgear router, you need to unplug it from its wall socket, hold on for some time, and then, plug it back into its socket. In a few minutes, you will be able to troubleshoot the issue at hand.
- Plug in the WiFi Router Properly
In case the aforementioned troubleshooting hack did not help you to resolve the issue at hand, then it might be because the Netgear wireless router is not properly plugged into its wall socket due to which it is receiving an inadequate power supply.
To take care of the problem, you need to check if the power cable connecting the router to the socket has cuts. In case, it does, then you should tape the cable up. Apart from that, ensure that the wall outlet is not damaged.
- Replace the Ethernet Cable
Sometimes, a damaged Ethernet cable or a loose Ethernet connection can also become a factor leading to the Netgear router red light issue. To troubleshoot it, you need to replace the existing cable with a new one and ensure a finger-tight connection between the devices.
Along with this, make sure that the Ethernet ports located on the Netgear wireless router as well as the existing modem are not damaged. Otherwise, more technical issues will knock at your door without even warning you first.
- Update the Router Firmware
When was the last time you updated the firmware of your Netgear wireless router? If you do not remember it, then it is a sign that you ought to do it now. Or else, you might also get stuck with issues like www.routerlogin.net refused to connect in the future.
In case you want to be sure of the instructions to execute the Netgear router firmware update process, then it is recommended that you pay attention to the steps given in the user manual of your networking device.
- Do Netgear Router Setup Again
In case none of the aforementioned troubleshooting hacks worked for you to resolve the Netgear router red light issue, then the time has come for you to set up your Netgear wireless router from scratch.
For your information, there are three different methods via which you can install your networking device. The first one is the WPS method, the second is the Manual method, and the third is by using the Nighthawk app.
Conclusion
This was all about the troubleshooting tips via which you can resolve the Netgear router red light issue. Hopefully, one of the hacks mentioned in this article was able to help you to turn the red LED on your networking device to green.
Check Also: My Netgear Router is Not Sending a Wireless Signal. Help!